Eastern Instruments - Solids Mass Flow and Air Flow Measurement Equipment

Not all Solids Mass Flow Meters are created equally, so how do you know which meter is best suited to measure your product??? When asking this question, the best answer is, when in doubt, test some product!  Most manufacturers of mass flow meters should have a test lab and a list of products that they have tested with their devices, building a database of what works and what does not work. WHAT TO LOOK FOR WHEN EXPLORING THE TESTING OPTION? REPLICATE THE INSTALLATION - Testing a product sample should also be done in a way that replicates the application or installation location.  This means that the equipment being used for testing should be similar to that of what will be used in the field.  For example, if the application calls for a flow meter (flowmeter) to be installed under the discharge of a screw conveyor, then the testing lab should have a screw conveyor. Simulation of Screw Conveyor Feeding a CentriFlow Type II Meter Simulation of Belt Fee...

When measuring the mass flow of air flow in a duct or pipe, using the correct flow element is half the battle .  After deciding that using a differential pressure device like a Velocity Averaging Pitot is the right way to go, getting the correct instrumentation to measure that differential pressure is not something that every transmitter can do. VAP³ Velocity Averaging Pitot In typical industrial, combustion, and power generation applications , the differential pressure to be measured ranges from a high of 8 to 10 inches of water column down to 0.25 inch of water column or even less.  Getting a transmitter that can measure these ranges and have a turndown that can measure the low end accurately usually requires getting a laboratory type of transmitter, rather than an industrial differential pressure transmitter.  These are typically not satisfactory for these types of applications, so most users go with an industrial transmitter that has a very large URL (upper ran...

When measuring the flow of air or gas in a duct or pipe, accuracy is dependent on the type of device used to make the measurement, but is very dependent on the flow profile in the duct or pipe.  For example, if the flow in the duct or pipe is turbulent, many types of flow measurement devices will not even be able to measure the flow or have such an error you would be better off not having the measurement at all.  Here we will look further into turbulence and ways to minimize or eliminate it so that an accurate air flow measurement can be made. What is Turbulence? Turbulence can come in many forms, for example the flow could be spinning in the duct (cyclonic flow), or the flow could be going in the opposite direction than it is supposed to be going (reverse flow), or it can be off to one side or even angular (not parallel to the center-line of the duct or pipe).  When a flow sensor, averaging pitot tube, thermal mass sensor (thermal dispersion), venturi, or even an ori...

There are many different ways to move solid materials through a process, ranging from belt conveyors, vibratory conveyors, and pneumatic systems, to bucket conveyors/elevators and screw conveyors.  Many of these devices are great for moving the product, but if you need to measure the mass flow rate or control the flow rate, pulsations created by some of these devices can cause major problems. Devices like bucket conveyors/elevators, rotary valves, and screw conveyors have pockets, flights, or buckets that help to collect the product and move it through the device.  These create pulses or slugs of flow, some of which can be very large and there can be seconds or even moments where there is no flow at all between slugs. Pulsating Flow through a CentriFlow Meter Most mass flow meters require that pulsations be mechanically smoothed if at all possible, because they cannot deal with the pulsations when measuring the flow and computing the totalization.  This is typ...

When measuring the flow rate and totalization of a bulk solid materials with a flow meter, there are a lot of options.  However, when the particles of the bulk solid are large, irregular shaped, and vary greatly in bulk density, the options quickly dwindle down to a few. Large Bulk Materials like tobacco, recycled plastic bottles, recycled carpet pieces, trash, construction debris, biomass feed stocks (like wood products, hay, straw, and leaves) and the like are not only difficult to move through a process, but their product characteristics make it almost impossible to accurately measure the flow. Biomass Materials - Hay/Straw Biomass Materials - Wood Chunks/Chips Recycled Plastic Bottles Construction Debris To get an accurate mass flow measurement of bulk solids with large particles and irregular product characteristics the mass flow meter that is used must be able to measure the flow and have no dependence on these varying product characteristics like bulk de...

Even though it does not feel like it here in the Eastern US, it is definitely winter in many parts of the world.  And something happens every winter at process plants all around the world, namely instruments and instrumentation begin to have issues due to the temperatures, moisture, and the winds of winter.  These issues send Instrumentation Techs, Engineers, and Maintenance people scrambling to get them back online and functioning properly. One of the biggest issues is when an instrument that is crucial to the proper operation of the a plant gives erroneous readings or stops working all together.  This is especially the case with flow measurement devices and instruments.  Having a transmitter or moisture in the differential pressure lines freeze up will cause the transmitter to stop responding or give incorrect flow measurement readings.  These can be handled sometimes (depending on the temperatures) by putting the transmitters inside a building or under a...

When it comes to measuring the flow rate of air or gas in a duct, there are many different devices used.  For example, there are thermal sensors, hot wire anemometers, rotating vane anemometers, static pressure drop devices (venturi, orifice plate), and differential pressure devices (pitot, annubar, primary element).  The most widely used and considered a true measurement of the flow is the differential pressure device.  The most widely used differential pressure device is a velocity averaging pitot tube. Velocity Averaging Pitot Tube The velocity averaging pitot tube is a device that when inserted into the air or gas flow stream, provides a high pressure measurement port and a low pressure measurement port.  The high pressure port measures the total pressure created when the air or gas stream impacts the port, where the low pressure port typically measure the static pressure in the duct. VAP³ Velocity Averaging Pitot Tube from Eastern Instruments The dif...